Because you need Administrator privileges to access the BCD file with BCDEDIT. So, be sure to run the Command Prompt

using a RIGHT-CLICK and selecting:

("Run as administrator").

The following is what you would typically see when entering the command bcdedit all by itself:

C:\>bcdedit

Windows Boot Manager
--------------------
identifier              {bootmgr}
device                  partition=\Device\HarddiskVolume1
description             Windows Boot Manager
locale                  en-US
inherit                 {globalsettings}
default                 {current}
resumeobject            {ad68f292-2870-11e3-9c80-856fbacd7f33}
displayorder            {current}
toolsdisplayorder       {memdiag}
timeout                 30

Windows Boot Loader
-------------------
identifier              {current}
device                  partition=C:
path                    \Windows\system32\winload.exe
description             Windows 7
locale                  en-US
inherit                 {bootloadersettings}
recoverysequence        {ad68f294-2870-11e3-9c80-856fbacd7f33}
recoveryenabled         Yes
osdevice                partition=C:
systemroot              \Windows
resumeobject            {ad68f292-2870-11e3-9c80-856fbacd7f33}
nx                      OptIn

Note that the Boot Manager program (bootmgr) is often located in a volume without a drive letter, such as in this example, but it could have one. If there were only one partition on the drive, then it would appear in the C: partition.

The following is a dump of a Windows™ 7/8 (or Vista) Administrator console (Command Prompt window) after entering "help bcdedit" ("bcdedit /?" will give the same):

Moto G6 Xt19256 Firmware Link

There are two primary methods: Using Minimal ADB and Fastboot Tools (Manual) or the Lenovo Moto Smart Assistant (Automatic). Method 1: Using Fastboot Commands (Manual) Minimal ADB and Fastboot on your PC. Download the Firmware

Connect to PC and verify connection: fastboot devices moto g6 xt19256 firmware link

Press and hold the and Power buttons simultaneously for 5 seconds.

If your drivers are installed correctly, you will see your device's serial number listed in the terminal window. Step 4: Flash the Firmware

You flashed the wrong modem. Re-flash only the modem files from the correct XT19256 firmware: fastboot flash modem NON-HLOS.bin | | Stuck in fastboot loop | Re-run

fastboot oem fb_mode_set fastboot flash partition gpt.bin fastboot flash bootloader bootloader.img fastboot flash modem NON-HLOS.bin fastboot flash fsg fsg.mbn fastboot erase modemst1 fastboot erase modemst2 fastboot flash dsp adspso.bin fastboot flash logo logo.bin fastboot flash boot boot.img fastboot flash recovery recovery.img fastboot flash system system.img_sparsechunk.0 fastboot flash system system.img_sparsechunk.1 fastboot flash system system.img_sparsechunk.2 fastboot flash system system.img_sparsechunk.3 fastboot flash system system.img_sparsechunk.4 fastboot flash system system.img_sparsechunk.5 fastboot flash system system.img_sparsechunk.6 fastboot flash system system.img_sparsechunk.7 fastboot flash system system.img_sparsechunk.8 fastboot flash oem oem.img fastboot erase cache fastboot erase userdata fastboot oem fb_mode_clear fastboot reboot

Extract the ZIP file to an accessible folder on your PC, such as C:\platform-tools . 3. Moto G6 XT1925-6 Firmware Files

The Moto G6 XT1925-6 shipped with Oreo (8.0) but was updated to Pie (9.0). If your device has ever booted Android 9, the bootloader and partition table (gpt.bin) were upgraded.

Note: What you see above is exactly how a Vista/Win7/8 display appears; and, yes, the word "Command" in the last heading was spelled wrong by Microsoft, it should be plural (Commands) just like all the others. And if there really was only one, then the word "control" should have had an 's' after it! This was still true for a Windows 7 SP1 install we examined, and even Windows 8.1. Is this a case of "If it ain't broke, don't fix it!"? Apparently, the cost of qualifying a revised program outweighs this grammatical error.

And even though Windows™ 10 added six new commands (shown in white below), they doubled the same grammatical error (shown in red). Now it's incorrect for both of the last two command types:

Connect to PC and verify connection: fastboot devices

Press and hold the and Power buttons simultaneously for 5 seconds.

Type fastboot devices and press enter. You should see your device serial number.

If your drivers are installed correctly, you will see your device's serial number listed in the terminal window. Step 4: Flash the Firmware

You flashed the wrong modem. Re-flash only the modem files from the correct XT19256 firmware: fastboot flash modem NON-HLOS.bin

Extract the ZIP file to an accessible folder on your PC, such as C:\platform-tools . 3. Moto G6 XT1925-6 Firmware Files

The Moto G6 XT1925-6 shipped with Oreo (8.0) but was updated to Pie (9.0). If your device has ever booted Android 9, the bootloader and partition table (gpt.bin) were upgraded.

C:\>bcdedit /export /?

bcdedit /export <filename>

This command exports the contents of the system store into a file.  This file
can be used later to restore the state of the system store.  This command is
only valid for the system store.

<filename>          The filename to be used as the destination for the export.
                    If the filename contains spaces, it must be enclosed in
                    quotation marks ("").

Example:

The following command exports the system store to the specified file:

    bcdedit /export "C:\Data\BCD Backup"

After examining this backup file in our Documents folder (using HxD), our first reaction was: "Man, this thing appears to be full of all kinds of needless 'gunk'!" It even saves the path and filename to this backup file, inside the file itself!

Then we compared it to the original BCD file by making a copy of that file while the OS was offline (connected as a slave drive to a different OS), and found there were MANY differences! So, the 'backup copy' is not really a true copy. And the differences go well beyond simply changing the path name of its location.

So why is this file so 'cluttered' compared to the Windows XP boot.ini file? Its first 4 bytes are a big clue: "regf". Reason: The BCD file has the same format as a Windows Registry hive! (For example, the NTUSER.DAT file begins with the same 4 bytes.) And in fact, once a Windows Vista/7/8 OS has actually started booting-up, it loads the BCD file into the Windows Registry at: HKEY_LOCAL_MACHINE\BCD00000000.

What happens if we change the NT Disk Signature on a Windows 7 disk drive?

To test this, we used a disk editor to alter the bytes at offsets 0x1B8 through 0x1BB in the MBR (first sector of the disk drive) by simply adding 1 to each byte. If you attempt to boot a PC after doing that, you'll see the following BLACK error screen:

In previous Windows versions, the OS would still boot up this way; even though there was the possibility some program that used the Disk Signature could then have problems. Note: The same error message, with Status: code of 0xc000000e, will also be displayed if we change those NT Sig. bytes to all zeros! Only if you edit these bytes back to their original values will the PC boot-up again.

It's also possible to see such an error if your PC is somehow directed to start booting from a drive other than the normal boot drive, and the BCD Store on that drive points to the first drive, which will obviously contain a different Disk Sig. than what is stored in that drive's BCD. Most PC BIOS have a 'Boot Menu' (often accessible using the F12 key at boot-up) which temporarily makes whatever drive you select, be the first drive on the PC, so a Windows 7, 8.1 or 10 OS on that drive will not have this error! (Note: Unless you plan on always keeping an original Windows OS drive and a new Windows OS drive both connected to your PC, you should never do a new OS install with any other drives connected to the PC!) Why? Because new Windows OS installs often make changes to a primary disk drive, even when installed to a secondary drive! Disconnect all but the disk drive you intend to install a new Win OS on, and in the future you will be able to boot-up the new drive all by itself (or using a Boot Menu key) without it depending upon some primary disk drive you decided to remove, or that has failed.

NOTE: The error shown above is a function of the bootmgr program! We know this, because the same error message will be displayed after altering the NT Disk Signature on a drive that has had its entire C: Volume (where the actual Windows OS resides) removed! So, the Boot Manager must check the NT Disk Signature before it even looks for the presence of the C: Volume.

But how does bootmgr know what those hex bytes should be?

Answer: After examining both our copy and the original BCD file, we found the NT Disk Signature there, in the same order as found in the MBR Sector, no less than 9 times. For our small test install of a new Windows 7 OS, this shows where those bytes occurred (highlighted with a pink background color); along with all the other data contained in a BCD Store file. Note: The \Boot folder of your System Reserved partition will also contain a few LOG files: BCD.LOG, BCD.LOG1 and BCD.LOG2, but the numbered files are often empty. This LOG file is a copy of the BCD file, having the same location written inside it and all the general indications of a BCD Registry file, but about half its bytes may be different.

Why is it so difficult to move the C: Volume under Windows 7 or later?

To clarify: Under most previous Windows installs, such as Windows 98, people who performed multi-booting or simply had many different partitions on their PCs often used a program called Partition Magic to shrink or even completely rearrange the layout of partitions on their disk drives. But attempting to change where the C: Volume begins under Windows 7 results in a similar BLACK screen error as above; including the same exact message: "Info: The boot selection failed because a required device is inaccessible." But with a different code: "Status: 0xc0000225."

[Note: This is true whether the correct location is specified in the Partition Table or not; same Status code will be shown in either case. In fact, we doubt that bootmgr even looks at the Partition Table, provided it can find the C: volume where it is supposed to be!]

This problem is similar to the one above (concerning the NT Disk Signature), but involves the exact sector location of the C: drive's partition.

So where in the BCD file, is the sector location of the Windows Boot Sector stored?

The reason for the question being: Although we can find our drive's NT Disk Signature in the BCD Store, we can not find a sector location for the C: drive! Before searching, we had thought only the BCD file would need to be updated if we moved the C: Volume. We knew how partitions are referenced in a Windows REGISTRY (see NTFS Disk Signature), but could not find any similar bytes; other than the 4 bytes of the NT Disk Sig., in our BCD file! So how does bootmgr know where the sector offset location of a C: drive should be, and prevent booting from an OS volume we simply moved and did not resize; even though the data in both the Partition Table and its Boot Sector (Hidden Sectors which give us sector offset to Boot Sector) have already been updated?

Could it be as simple as the OS already having accessed the REGISTRY; with much of the system already running in Memory, it then finds the offset stored there does not match the values in the Partition Table and/or Boot Sector, so it gives us essentially a false message, stating: "The boot selection failed because a required device is inaccessible."? Yet, the bootmgr program could only know that if it did find and access the Registry.

Other Experiments:

2. We next carried out the following steps on a copy of our Windows 7 OS install in order to verify our theory about why Windows 7 does this:

A) Copy the hidden file bootmgr and various folders (including "Boot\enUS" and "Boot\Fonts") from the "System Reserved" partition to the root directory of the C:\ drive. Note: Five or six files must be 'skipped' when doing this, because the BCD Store (and associated files) will remain in use by the OS (preventing them from being copied)!
B) Create a copy of the BCD file in C:\Boot by using this command (as Administrator): bcdedit /export C:\Boot\BCD
C) Change the MBR Sector, so the main OS partition is the 'Active' partition.

After that we were able to boot-up the OS from only the C: drive. In order to prove this is true, we used HxD to zero-out the entry in the Partition Table for the System Reserved partition. (Note: The reason we did not use Windows to 'delete' the partition, is because that could have ruined being able to access it again in the future. By saving those hex bytes elsewhere and zero-filling the entry, we can simply enter those bytes in the table again, in order to restore and access the partition!) Upon rebooting and opening the Disk Management utility, one can graphically see this is true:

D) We shrank the size of this Volume (C:) to only 8 GB in order to run the next test below.

What about BOOTSTAT.DAT and BOOTSECT.BAK files?

E) shift the beginning of the C: drive to where the System Reserved partition had been, by correcting the data in both the Boot Sector (VBR) and the Partition Table; not to mention, actually moving the Boot Sector and its following Volume Boot Record sectors as well

Moto G6 Xt19256 Firmware Link

Moto G6 Xt19256 Firmware Link

Moto G6 Xt19256 Firmware Link

Moto G6 Xt19256 Firmware Link

What happens if we change the NT Disk Signature on a Windows 7 disk drive?

Why is it so difficult to move the C: Volume under Windows 7 or later?

Other Experiments: